In short
The power supply runs your door access reader and EM lock 24/7. Why a cheap unit causes doors that don't lock, reboots and dead batteries, and what to look for.
The power supply is the part of a door access system that keeps the door locked. It powers the reader and the electromagnetic (EM) lock 24 hours a day and charges the backup battery. A cheap or undersized power supply is one of the most common reasons a door stops locking properly, the reader keeps restarting, or the door releases during a short power dip.
Key Takeaways
- An EM lock only holds while it has steady power. If the voltage sags, the lock holds the door less firmly, and if the power goes, a standard EM lock releases.
- A good power supply gives a stable, regulated 12V output with spare capacity, so it runs cool in a closed box in Singapore’s heat and humidity.
- The power supply also charges the backup battery. Poor charging shortens battery life, and a weak battery leaves the door unlocked in an outage.
- Our door access packages use a premium quality IMPAQ 12V 5A power supply with a 12V 7.5AH backup battery, and every package comes with a 1-year onsite product and service warranty.
What the power supply does in a door access system
A typical single-door system has a reader (card, PIN, fingerprint or face recognition), an EM lock on the door frame, an exit release button, an emergency break glass and a power supply with a backup battery. Our guide on how door access systems work shows how they are wired together.
The power supply has three jobs:
- Power the EM lock continuously. An EM lock is a magnet that holds a steel plate on the door. It holds only while current flows through it, all day and all night.
- Power the reader. The reader and its controller need clean, steady power to read cards, fingers or faces and to switch the lock.
- Charge and switch to the backup battery. When the mains power fails, the power supply switches the lock and reader to the battery and then recharges it when power returns.
What goes wrong with a cheap power supply
Many door access faults come from the power side of the system rather than the reader. Common symptoms are:
- The door does not lock firmly or can be pulled open. An EM lock’s holding force is rated at its correct voltage. An unstable or overloaded supply that sags under load lets the magnet hold less firmly. See the benefits of magnetic locks for how a maglock holds the door.
- The reader restarts or freezes. Voltage dips and electrical noise when the lock switches can make the reader reboot, lose its settings or stop responding.
- The door releases during a short power dip. If the supply cannot switch smoothly to the battery, or the battery is weak, the lock drops even in a brief outage.
- The battery dies early. Poor charging over-charges or under-charges the battery, so it swells or can no longer hold the door when it is needed.
- The power supply box runs hot. A unit working at its limit inside a closed metal box in a warm ceiling or riser ages quickly and fails sooner.
What to look for in a door access power supply
| Feature | Why it matters |
|---|---|
| Regulated 12V DC output | Keeps the EM lock at its rated holding force and the reader stable. |
| Spare current capacity | A supply that only just covers the lock and reader runs hot. Headroom keeps it cool and lets it charge the battery at the same time. |
| Built-in battery charging and changeover | Switches to the backup battery without dropping the lock, and recharges it properly afterwards. |
| Short-circuit and overload protection | Protects the lock, reader and wiring if a cable is damaged. |
| A proper enclosure | Holds the supply and battery safely and keeps them away from tampering. |
Place the power supply and backup battery inside the secured area, not on the outside of the door, so nobody can cut the power to open it. Our guide to planning an office access control system covers where each part should go.
Why the backup battery matters
A standard EM lock is fail-safe: it releases when it loses power, so people can always get out. That is good for safety, but it also means the door is unlocked during a power cut unless the backup battery keeps it powered. A healthy 12V 7.5AH battery, charged correctly by the power supply, keeps the reader and lock working through a short outage. How long it lasts depends on the lock, the reader and the battery’s age.
Check the battery during maintenance and replace it when it no longer holds a charge. A swollen battery or one that is warm to the touch should be replaced straight away.
What our door access packages include
Every CCTVSG.NET door access package includes:
- A premium quality IMPAQ 12V 5A power supply
- A 12V 7.5AH backup battery
- A 600lb electromagnetic lock with ZL / U bracket
- An exit release button and an emergency break glass
- Your choice of reader: PIN and card, Hikvision fingerprint, or Hikvision face recognition
Single-door packages start at S$490 for PIN and card, S$570 for fingerprint and S$680 for face recognition. Every package comes with a 1-year onsite product and service warranty and technical support. Compare the readers in our guide to card, fingerprint and face recognition door access.
See our door access and intercom packages with prices, or send us a photo of your door on WhatsApp and we will recommend the right package.
Frequently asked questions
- What power supply does a door access system need?
- Most single-door systems with a 12V EM lock use a regulated 12V DC power supply with spare capacity, battery charging and a backup battery. Our packages use a premium quality IMPAQ 12V 5A power supply with a 12V 7.5AH backup battery.
- Will my door unlock if the power goes off?
- A standard EM lock releases when it loses power. The backup battery keeps the lock and reader working through a short outage, as long as the battery is healthy and the power supply charges it correctly.
- Why does my door access reader keep restarting?
- Frequent restarts are often caused by an unstable or overloaded power supply, voltage dips when the lock switches, or a failing backup battery. Have the power supply and battery checked before replacing the reader.
- Is there a warranty?
- Yes. Every package comes with a 1-year onsite product and service warranty and technical support.
Want this done for you?
We supply and install CCTV, door access, video intercom and Wi-Fi systems across Singapore, from Hikvision, Uniview, Vstarcam, TP-Link, Ruijie and EZVIZ. Send a photo or floor plan and we will recommend a setup and a fixed price.





